LF1031FP-INS-LAB-RevA11 © 2011 GF Health Products, Inc.Read this manual before operating your Patient Lift.Save this manual for future use.The most cu
1031FP-INS-LAB-RevA11 106. Screw the push handles into the mast and tighten the nuts.7. Insert spreader bar attachment rod into spreader bar. Insert
1031FP-INS-LAB-RevA11 116 OPERATING INSTRUCTIONSLIFTING THE PATIENT WARNING: Do not attempt to transfer a patient without prior approval of the pati
1031FP-INS-LAB-RevA11 12Lifting the patient from the oor1. Position the patient lift behind the patient, placing a pillow over the base to protect a
1031FP-INS-LAB-RevA11 13ping forward.Removing the slingGently pull the leg sections to the side, out from under the patient’s thighs. Standing by the
1031FP-INS-LAB-RevA11 147 CARE AND MAINTENANCEProper care and maintenance are essential to keeping your Lumex patient lift in a safe operating condit
1031FP-INS-LAB-RevA11 15CLEANINGRegular cleaning is recommended. A soft cloth, dampened with water and a mild NON-ABRASIVE detergent (household cleane
1031FP-INS-LAB-RevA11 16INSTALLATION OF 1010S005 HYDRAULIC PUMPRemoval of Existing Pump1. Follow the instructions in this section to remove the exist
1031FP-INS-LAB-RevA11 17Installation of New PumpInfo: The hardware for attaching the Hydrau-lic Pump (GF #1010S005) to the mast and boom comes with th
1031FP-INS-LAB-RevA11 18MAINTENANCE SCHEDULEInfo: Only qualified persons should service and repair your Lumex patient lift. Regular maintenance of your
1031FP-INS-LAB-RevA11 198 TROUBLESHOOTING WARNING: If you experience a problem with your lift and are unable to service it your-self, contact your L
1031FP-INS-LAB-RevA11 2GF Health Products, Inc. is not responsible for typographical errors. Packaging, warranties, products and specications are sub
1031FP-INS-LAB-RevA11 209 SPECIFICATIONS *Info: All dimensions are given in inches unless otherwise specified.Basewidth Open:39.7"Closed:25.4&
1031FP-INS-LAB-RevA11 2110 LIMITED WARRANTYGF Health Products Inc. warrants this product to be free from manufacturing defects in material and workma
1031FP-INS-LAB-RevA11 22TIVE PRODUCT OR PART PURSUANT TO THE TERMS CONTAINED HEREIN. GF HEALTH PRODUCTS, INC. SHALL NOT BE LIABLE FOR ANY CONSEQUENTIA
1031FP-INS-LAB-RevA11 2311 INDEXAAssembly instructions 8BBefore each use 14CCare and maintenance 14Care of slings 15CAUTION statement, signicanc
USA Company Headquarters:GF Health Products, Inc. 2935 Northeast Parkway Atlanta, Georgia 30360 USAtel: 770-368-4700www.grahamfield.comMade in Taiwan
1031FP-INS-LAB-RevA11 31 INTRODUCTIONCongratulations on your purchase of a Lumex patient lift. The following pages will provide you with important sa
1031FP-INS-LAB-RevA11 42 SAFETY PRECAUTIONSIMPORTANT: Before using patient lift, please read and adhere to the following safety precautions and warni
1031FP-INS-LAB-RevA11 5 WARNING: Replace any worn or broken parts immediately! Torn, cut, frayed, or broken slings can fail, resulting in personal in
1031FP-INS-LAB-RevA11 63 FEATURESpush handle6-point spreader bar(suspension)hydraulic pumppump knob(pump locking and unlocking)adjustment handle(boom
1031FP-INS-LAB-RevA11 74 HANDLING PROCEDURESSHIPPING AND TRANSPORTATION INSTRUCTIONSIf the patient lift is to be reshipped by common carrier, it shou
1031FP-INS-LAB-RevA11 85 ASSEMBLY INSTRUCTIONSComponents are shown in illustration below and called out in list below illustration.COMPONENTSComponen
1031FP-INS-LAB-RevA11 9ASSEMBLY1. Remove the locking pin from the mast sleeve located on the rear of the base.2. Install the L-inserts in the base.3
Kommentare zu diesen Handbüchern